Protective Design and Vehicle Mitigation Glossary
Short, standards-based definitions of the terms used in hostile vehicle mitigation, barrier crash testing, antiterrorism design and explosives safety. PNH Security Engineering Consultants uses each term as the governing standard defines it.
Glossary by Pedram Hesam, PhD, PSP, Chief Technical Officer, PNH Security Engineering Consultants. Updated .
Vehicle barrier ratings and testing
A vehicle barrier crash rating records the test vehicle, impact speed and penetration that one barrier achieved in a full-scale test under a named standard.
Vehicle security barrier (VSB): A vehicle security barrier is a passive, active, portable or linear barrier used to prevent potentially hostile vehicular access to a site (ISO 22343-1:2023).
ASTM F2656: ASTM F2656/F2656M-23 is the U.S. full-scale test method that rates a barrier by test vehicle, impact speed and penetration, using six vehicles from a 2,420 lb car to a 65,000 lb heavy goods vehicle striking at 90 degrees. See the crash ratings guide.
M30, M40, M50: M30, M40 and M50 are the ASTM F2656 condition designations for the 15,000 lb standard test truck (M) at nominal 30, 40 and 50 mph, with actual test speeds of 28.0 to 37.9, 38.0 to 46.9, and 47.0 mph or more.
P1, P2, P3 penetration rating: The P rating is the ASTM F2656 band for how far the vehicle traveled past the barrier: P1 is 1 m (3.3 ft) or less, P2 is 1.01 to 7 m (3.31 to 23.0 ft) and P3 is 7.01 to 30 m (23.1 to 98.4 ft). P2 and P3 are reported with the measured distance, for example P2:6.4 m.
Dynamic penetration: Dynamic penetration is the maximum distance the vehicle reference point travels past the barrier's pre-test leading impact edge during the crash, not the static distance. Under ASTM F2656 the reference point is the cargo bed's leading lower edge for trucks and the A-pillar base for cars and pickups.
ASTM F3016 and S10, S20, S30: ASTM F3016/F3016M-19 is a low-speed test method for storefront and pedestrian-area devices, using a 5,000 lb surrogate vehicle at nominal 10, 20 or 30 mph (S10, S20, S30). Its P1 (1 ft or less) and P2 (1 to 4 ft) ratings differ from ASTM F2656 P ratings. See storefront protection.
ISO 22343-1: ISO 22343-1:2023 is the international impact test method that rates a barrier by its measured vehicle class and mass, speed, angle, penetration and major debris distance, for example V/7200[N3C]/48/90:2.6/5.0 (illustrative).
ISO 22343-2: ISO 22343-2:2023 is the international application standard that gives end users guidance on the selection, installation and use of vehicle security barriers, including vehicle speed (9.2), the vehicle dynamics assessment (9.2.2) and impact angle (9.3).
IWA 14-1: IWA 14-1:2013 is the International Workshop Agreement test and rating method that ISO 22343-1:2023 cancels and replaces. The UK National Protective Security Authority (NPSA) treats existing results as valid unless the as-tested barrier has changed.
PAS 68: PAS 68 is the withdrawn British Standards Institution impact test specification for vehicle security barriers, which measured penetration from the barrier's rear face; NPSA treats existing results as it does IWA 14-1 results.
K4, K8, K12: K4, K8 and K12 are legacy U.S. Department of State ratings for a 15,000 lb truck at nominal 30, 40 and 50 mph, replaced in U.S. practice by ASTM F2656 condition designations. K12 is not automatically M50-P1, because the two measure penetration differently.
Major debris distance: Major debris distance is the distance from the barrier's original front face to the furthest piece of major debris after an ISO 22343-1 impact test, reported as the last value in the rating code. ASTM F2656 and ASTM F3016 do not include debris in their ratings.
Crash-rated vs crash-tested: Crash-rated means a full-scale test of that model and configuration met a named standard and edition; crash-tested only means a test was run, which may have failed.
Vehicle dynamics and approach
The impact condition at a barrier line is the speed, angle and kinetic energy a credible vehicle can reach there, set by run-up distance and approach geometry.
Hostile vehicle mitigation (HVM): Hostile vehicle mitigation is the protective security discipline focused on reducing the risks associated with vehicle-borne threats (NPSA). See hostile vehicle mitigation.
Vehicle ramming: Vehicle ramming is deliberately driving a vehicle at an individual or into crowds of people to cause harm. NPSA's broader term, vehicle as a weapon, also covers driving into infrastructure to damage or disrupt it. See vehicle ramming assessment.
Vehicle dynamics assessment (VDA): A vehicle dynamics assessment is an engineering calculation of the speed, approach angle and kinetic energy a credible threat vehicle can reach at each barrier line. See the vehicle dynamics assessment guide.
Run-up distance: Run-up distance is the length of drivable path over which a vehicle can accelerate toward a barrier line, measured along the route it would actually drive. From rest at constant acceleration, speed grows with the square root of distance, so doubling the run-up raises speed about 41 percent.
Impact speed: Impact speed is the speed of a vehicle when it reaches the barrier. It is calculated per barrier line and is usually well below the vehicle's top speed.
Impact angle: Impact angle is the horizontal angle at which a vehicle strikes a barrier. ASTM F2656 and F3016 test at 90 degrees, while ISO 22343-1 allows any angle above 0 and up to 90 degrees and states it in the rating.
Kinetic energy (KE): Kinetic energy is the energy a moving vehicle carries into a barrier, KE = 1/2 m v^2 (m in kg, v in m/s, giving joules), and UFC 4-022-02 gives KE = 0.0334 W V^2 in foot-pounds (W in pounds, V in mph).
Antiterrorism and building standards
Department of Defense (DoD) antiterrorism design is governed by UFC 4-010-01, which sets minimum standards for inhabited buildings.
Antiterrorism/force protection (AT/FP): In the DoD Dictionary, antiterrorism is defensive measures used to reduce the vulnerability of individuals and property to terrorist acts, including rapid containment by local military and civilian forces; force protection is preventive measures taken to mitigate hostile actions against DoD personnel, resources, facilities and critical information. See antiterrorism and force protection.
UFC 4-010-01: UFC 4-010-01 is the Unified Facilities Criteria document that sets the minimum antiterrorism requirements for new construction and major renovations of inhabited DoD buildings and inhabited tenant buildings on DoD installations. Its 2026 digital reissue also carries the design criteria process formerly in UFC 4-020-01. See the UFC 4-010-01 guide.
UFS 4-010-01: UFS 4-010-01 is the Unified Facilities Supplement to UFC 4-010-01, dated 30 September 2026, with commentary, recommendations and planning cost tables; it binds a project only if the contract explicitly includes it.
Standoff distance: Standoff distance is the distance between a protected asset and the closest point a vehicle or explosive device can reach. Where land allows, it is the least expensive protection against vehicle bombs. Against a moving vehicle it is measured to the barrier line, and rated penetration must not use up the required standoff.
Progressive (disproportionate) collapse: Progressive collapse is the spread of an initial local failure from element to element, eventually resulting in the collapse of an entire structure or a disproportionately large part of it (ASCE 7 commentary, quoted in UFC 4-023-03). DoD now addresses it through UFC 3-301-01, Chapter 8, applying ASCE/SEI 76-23 with modifications. See blast-resistant design.
Blast and explosives safety
DoD sites explosives under DESR 6055.09, which sets quantity-distance separations by hazard division and NEWQD.
DESR 6055.09: The Defense Explosives Safety Regulation (DESR) 6055.09 sets DoD explosives safety criteria, including quantity-distance, and replaced DoD 6055.09-M, Volumes 1 to 8. The current version is Edition 1, Change 2, November 25, 2025.
Quantity-distance (QD): Quantity-distance is the minimum separation required between a potential explosion site (PES) and an exposed site (ES), set by the hazard division and the net explosive quantity at the PES. See the quantity-distance guide.
Hazard division (HD 1.1 to 1.6): Hazard divisions subdivide Class 1 explosives by the hazard they present: 1.1 mass explosion, 1.2 projection without mass explosion, 1.3 fire with minor blast or projection, 1.4 minor explosion hazard, 1.5 very insensitive with a mass explosion hazard, and 1.6 extremely insensitive articles without a mass explosion hazard. HD 1.5 is treated as HD 1.1 for QD.
Net explosive weight (NEW) and NEWQD: Net explosive weight is the total weight, in pounds, of all explosive substances (high explosive, propellant and pyrotechnic) in the ammunition and explosives; DESR 6055.09 uses it for transportation. NEWQD, the quantity used in QD, is the same total unless testing supports an approved different value; for HD 1.1 it is the total high explosive weight plus the total net propellant weight (DESR V1.E7.2.2.1).
Scaled distance (Z, K-factor): Scaled distance is distance divided by the cube root of explosive weight, written Z = R/W^(1/3) in blast engineering; for the same explosive and charge shape, the same scaled distance gives the same peak overpressure. QD uses D = K W^(1/3), with D in feet, W the NEWQD in pounds and K set by the risk assumed or permitted.
Inhabited building distance (IBD): Inhabited building distance is the QD separation required between a PES and inhabited buildings. For HD 1.1 above 30,000 lb NEWQD from a PES other than an earth-covered magazine it is 40W^(1/3) up to 100,000 lb (about 1.2 psi); below 30,000 lb, fragments and debris control.
Public traffic route distance (PTRD): Public traffic route distance is the QD separation required between a PES and a public traffic route, which DESR 6055.09 defines as any public street, road, highway, navigable stream or passenger railroad, including on-base roads routinely used by the public for through traffic. For HD 1.1 it is 60 percent of the applicable inhabited building distance.
Assessment and planning
A threat, vulnerability and risk assessment and a design basis threat define what a facility must resist before design begins.
Threat, vulnerability and risk assessment (TVRA): A TVRA is a structured assessment that identifies credible threats to a site, the vulnerabilities they could exploit and the consequences, then ranks the risks to set protection priorities. The Interagency Security Committee treats risk as a function of threat, consequence and vulnerability. See threat, vulnerability and risk assessment.
Design basis threat (DBT): A design basis threat is the defined threat a facility is designed to resist: the aggressor tactics and their severity, such as a vehicle and impact speed for ramming or an explosive weight for a vehicle bomb. Under UFC 4-010-01 it is set with a level of protection when the minimum standards are not adequate.
One-way attack drone: A one-way attack drone is an uncrewed aircraft intended for a single-use mission and equipped with an integrated explosive warhead, meant to fly into a target and detonate. The Congressional Research Service reports that DoD typically uses the term this way but does not appear to have published a public definition.
Passive anti-UAV protection: Passive anti-UAV protection is the use of physical measures, such as hardening, shelters, standoff, screening and dispersal, to reduce the effects of a drone strike on people and critical assets without detecting, jamming or destroying the drone. See passive anti-UAV protection.
How PNH uses these terms
PNH Security Engineering Consultants is an independent protective design and hostile vehicle mitigation engineering firm; it does not make, sell, hire or install products. To discuss a project, contact PNH.
References
- ASTM F2656/F2656M-23, Standard Test Method for Crash Testing of Vehicle Security Barriers, approved November 1, 2023, ASTM International (https://www.astm.org/f2656_f2656m-23.html)
- ASTM F3016/F3016M-19, Standard Test Method for Surrogate Testing of Vehicle Impact Protective Devices at Low Speeds, approved August 1, 2019, ASTM International (https://store.astm.org/f3016_f3016m-19.html)
- ISO 22343-1:2023, Security and resilience: Vehicle security barriers, Part 1: Performance requirement, vehicle impact test method and performance rating, edition 1, ISO (https://www.iso.org/standard/50080.html)
- ISO 22343-2:2023, Security and resilience: Vehicle security barriers, Part 2: Application, edition 1, ISO (https://www.iso.org/standard/81415.html)
- IWA 14-1:2013, Vehicle security barriers, Part 1: Performance requirement, vehicle impact test method and performance rating, ISO (https://www.iso.org/standard/64736.html)
- Hostile Vehicle Mitigation (HVM), National Protective Security Authority (https://www.npsa.gov.uk/hostile-vehicle-mitigation-hvm)
- HVM Impact Rated: rating system explained, NPSA, March 2024 (https://www.npsa.gov.uk/sites/default/files/cse-hvm-impact-rated-rating-system-explained-npsa-20240301.pdf)
- DS Certified Anti-Ram Vehicle Barriers, U.S. Department of State, October 3, 2006, reproduced in NRC ADAMS ML070880794 (https://www.nrc.gov/docs/ML0708/ML070880794.pdf)
- UFC 4-022-02, Selection and Application of Vehicle Barriers, 2009, Change 1, 2010, U.S. Department of Defense (https://www.wbdg.org/FFC/DOD/UFC/ufc_4_022_02_2009_c1.pdf)
- UFC 4-010-01, Antiterrorism, Force Protection and Security Engineering, digital UFC, Department of Defense via Whole Building Design Guide (https://www.wbdg.org/dod/ufc/ufc-4-010-01)
- UFS 4-010-01, Antiterrorism, Force Protection, and Security Engineering, 30 September 2026, Department of Defense via Whole Building Design Guide (https://www.wbdg.org/dod/ufc/ufs-4-010-01)
- UFC 4-023-03, Design of Buildings to Resist Progressive Collapse, 14 July 2009, Change 4, 10 June 2024, Section 1-3 (https://www.wbdg.org/FFC/DOD/UFC/ufc_4_023_03_2009_c4.pdf)
- Engineering and Construction Bulletin 2026-7, Clarification of Policies and Guidance Associated with Disproportionate Collapse, 23 February 2026, U.S. Army Corps of Engineers (https://www.wbdg.org/FFC/ARMYCOE/COEECB/ecb_2026_7.pdf)
- New Building Standard Paves the Way for Collapse-Resistant Structures (ASCE/SEI 76-23), NIST, June 5, 2023 (https://www.nist.gov/news-events/news/2023/06/new-building-standard-paves-way-collapse-resistant-structures)
- DOD Dictionary of Military and Associated Terms, as of November 2021, Joint Chiefs of Staff, entries for antiterrorism (JP 3-26) and force protection (JP 3-0) (copy at https://irp.fas.org/doddir/dod/dictionary.pdf)
- DESR 6055.09, Defense Explosives Safety Regulation, Edition 1, Change 2, November 25, 2025 (https://www.denix.osd.mil/ddes/denix-files/sites/32/2022/08/DESR-6055.09-Edition1-Change-2-251208.pdf)
- 49 CFR 173.50, Class 1, Definitions (https://www.law.cornell.edu/cfr/text/49/173.50)
- Scaling the Effects of Air Blast on Typical Targets, H. S. Morton, APL Technical Digest, Vol. 7, No. 1, September-October 1967, Johns Hopkins Applied Physics Laboratory (https://secwww.jhuapl.edu/techdigest/Content/techdigest/pdf/APL-V07-N01/APL-07-01-Morton.pdf)
- The Risk Management Process: An Interagency Security Committee Standard, 2021 Edition, CISA (https://www.wbdg.org/FFC/DHS/isc_risk_mgmt_process_2021.pdf)
- Defense Primer: Categories of Uncrewed Aircraft Systems, IF12797, Congressional Research Service, October 25, 2024 (https://www.congress.gov/crs_external_products/IF/PDF/IF12797/IF12797.2.pdf)
- Department of Defense Counter Unmanned Aircraft Systems: Background and Issues for Congress, R48477, Congressional Research Service, March 31, 2025 (https://www.everycrsreport.com/reports/R48477.html)
Editions change. PNH confirms the governing edition for each project.
Related Services

Hostile Vehicle Mitigation
Every credible approach route, the speed a vehicle can reach at each barrier line, and the tested rating that stops it.
Learn more →
Vehicle Ramming Assessment
A six-step assessment of every credible vehicle approach and the rating each barrier line needs.
Learn more →
Antiterrorism and Force Protection
Military and federal facilities brought into compliance with antiterrorism criteria, through submittal and review.
Learn more →Common Questions
What is the difference between crash-rated and crash-tested?
A crash-rated barrier passed a full-scale test of that model and configuration under a named standard and edition, documented in a test report. Crash-tested only means a test was run; the barrier may have failed, the test may have departed from the method, or a different configuration may have been tested. Ask for the full test report and check that the installed barrier matches the tested one.
What does M50-P1 mean?
M50-P1 is an ASTM F2656 rating meaning the barrier stopped a 15,000 lb standard test truck that struck it at 47.0 mph or more, with dynamic penetration of 1 m (3.3 ft) or less. Penetration is measured from the barrier's pre-test leading impact edge to the leading lower edge of the truck's cargo bed. The rating applies only to the barrier as tested, including its foundation.
What is standoff distance?
It is how far a protected building or asset sits from the nearest point a vehicle or explosive device can get to. Because blast pressure falls quickly with distance, more standoff means lighter, cheaper construction, and where land allows it is often the most economical protection. For a moving vehicle, the line that counts is the barrier line, and the barrier's rated penetration past that line has to be subtracted from the standoff available.
What is quantity-distance?
Quantity-distance (QD) is the rule set that tells you how far a stock of explosives must be kept from inhabited buildings, public roads, other magazines and operating buildings. The required distance depends on the hazard division and on NEWQD; where blast governs, as for larger HD 1.1 quantities, it grows with the cube root of the quantity, so doubling the explosives increases the distance by only about 26 percent. DoD criteria are in DESR 6055.09, and PNH applies them in explosives safety site plans.
Discuss Your Project With PNH
Send the site and the question. PNH replies within one business day.
- The siteAn address, a site plan or a few photos.
- The concernThe threat question, an incident or a client requirement.
- The criteriaAny standard or client specification that applies.
- The dateWhen the tender, review or decision is due.
Email pnhsec@pnhsec.com or call +1-818-253-9557